Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Killeen?
Gate repair in Killeen typically costs $150 to $450 for common fixes like a stuck slide gate, a bad sensor, or a control board that won’t respond, while larger repairs on heavy residential or commercial gates usually run $450 to $1,800. A full operator replacement pushes higher, and those are the two ends of the range most Killeen homeowners and property managers land between. The written estimate sets the final price, and we give that estimate free after we look at the gate.
What matters is the brand and the system. A LiftMaster or DoorKing setup on a commercial driveway behaves differently from a Ghost Controls or Mighty Mule gate at a home, and the technician who knows the brand logic finds the problem faster than one guessing. Our technicians have up to 13 years of experience, and our work is gates only: repair, electric gate repair, and new installation. Call (866) 722-0161. We answer 24/7.
Key Takeaways
- Typical Killeen gate repair: $150 to $450 for standard fixes, $450 to $1,800 for major repair.
- Control board or operator problems are the most expensive common repair.
- New gate installation runs more than repair in most cases, so we diagnose before recommending replacement.
- Estimates are free and the price is set per job by the written estimate.
- We work on your existing brand: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Gate Repair Cost Breakdown (2026)
Here’s how the numbers break down by job type in the Killeen market. These are typical ranges, not quotes. Heavy commercial gates, long spans, and older systems where parts have to be sourced sit at the top of each band, and simple residential fixes sit lower.
| Job Type | Typical Killeen Range | What’s Involved |
|---|---|---|
| Slide gate off track or stuck | $150 – $350 | Realignment, roller or track repair, hardware |
| Swing gate hinge or latch repair | $150 – $400 | Hinge replacement, sag correction, latch alignment |
| Safety loop or sensor replacement | $200 – $500 | Loop detector, photo eye, or safety edge swap |
| Remote, receiver, or keypad repair | $150 – $350 | Receiver module, remote programming, keypad or access hardware |
| Control board repair or replacement | $350 – $900 | Board diagnosis, replacement, reprogramming |
| Gate operator (motor) replacement | $800 – $1,800+ | Operator unit, mounting, wiring, calibration |
| Electric gate wiring repair | $250 – $750 | Low-voltage wiring, connections, power issues |
| Panel or frame repair (heavy gate) | $400 – $1,500 | Panel realignment, welding, structural repair |
| New gate installation | Estimate per job | Gate, operator, access control, full install |
What pushes a Killeen job toward the high end: the brand of the operator and whether the part is one we can source locally or have to order; the weight and length of the gate (14-foot residential driveway gates are lighter work than a 20-foot commercial slide gate); how much of the electric system is involved, since control boards and loop detectors cost more than mechanical hardware; and whether the gate is on a slope where the track and footing have shifted. What pulls it down: a single failed part, a repair we can finish with what’s already on hand, or a sensor problem we can resolve without replacing the whole access setup.
For a closer look at what a full repair visit covers, our gate repair overview walks through the service end to end.
What Affects Gate Repair Pricing in Killeen
Killeen sits in Central Texas, where the ground moves with the summer dry season and the gate posts and tracks feel it. That’s one of several local factors that shape what a repair costs here.
- Brand and system age. A LiftMaster or Linear system we know well often costs less to fix than an older operator where the control board is the issue and the replacement board has to be ordered. Knowing the brand shortens diagnosis.
- Clay soil movement. Central Texas clay swells after rain and shrinks in dry spells, and gate posts set in it shift over time. When the gate is out of square because the footing moved, repair includes realigning the gate, not just swapping a part.
- Electric vs. mechanical. Mechanical problems (hinges, rollers, tracks, latches) are almost always cheaper than electric ones. Control boards, operators, receivers, and loop detectors are the expensive repairs, and they’re where general handymen stop and a gate specialist takes over.
- Gate weight and span. Small-to-mid commercial property managers in Killeen with wide sliding gates and heavy panels pay more because the repair takes longer, needs bigger hardware, and often needs two technicians on site.
- Access control integration. If the gate shares a system with a keypad, intercom, or card reader, the repair may extend into that hardware. DoorKing and similar access systems add cost when the fix isn’t just the gate itself.
- Parts availability. Common brands and parts that are stocked locally keep a job in the lower band. A rare operator or an older model means an order delay and a higher total.
If you’re weighing a repair against a new gate, the decision usually comes down to how much of the system is failing. A gate that needs one part is a repair. A gate where the operator, the panel, and the access control are all past their useful life is where replacement starts to make sense, and new gate installation is a service we handle on its own. We diagnose first and replace only when necessary, so the recommendation reflects what’s actually wrong.
How to Save on Gate Repair
The biggest saving on a Killeen gate repair is catching the problem early. A gate that binds or hesitates is usually a cheap fix; the same gate run for months against a failing motor becomes a control board or operator replacement. Beyond that, a few practical moves keep the bill down:
- Get the estimate before any work starts. We give a free written estimate after looking at the gate, and the price is set per job by that estimate. No diagnostic fee, no surprise upcharge.
- Describe the brand and the symptom when you call. Telling us it’s a FAAC swing operator that won’t close, or a Mighty Mule that beeps and stops, lets us come prepared and shortens the visit.
- Fix the root cause, not the symptom. If the gate is off track because a post has shifted, realigning the gate fixes it; replacing a roller and leaving the post alone means the same repair again in a few months.
- Keep the gate clear and the track clean. Debris under a sliding gate and dirt in the track are the two most common causes of a gate that drags or stops. A quick clean now is free; a motor strain repair is not.
- Service the electric system when it first acts up. A receiver that intermittently drops signal or a loop detector that false-triggers is cheaper to diagnose than to replace. We handle receivers and loop detectors as standard electric gate repair, not an upsell.
A free estimate is the simplest way to know where you stand. Call (866) 722-0161 and we’ll set a time to look at the gate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Gate Repair Costs What It Does
A gate is a mixed system: mechanical parts, an electric operator, and access control all working together, and a problem in one shows up as a symptom in another. That’s why the diagnosis matters as much as the repair. A gate that won’t open could have a dead operator, a tripped loop detector, a failed receiver, or a control board that isn’t sending the signal. Each of those has a different price, and each is a job a generalist will often misread.
We work on your brand, not around it. Whether the gate is a LiftMaster residential slide operator, a DoorKing commercial access system, or a BFT swing gate, the technician starts from what that brand does when it fails rather than starting from scratch. That’s the difference between a repair that sticks and a repair that comes back.
Safety matters here too. Gate operators run on household power, and the wiring and control board on a gate are not a place for DIY work. A heavy swing or slide panel can crush, and a slide gate that comes off its track can fall. We recommend a trained technician for anything involving the operator’s wiring or a panel that’s out of alignment, and we don’t hand out step-by-step DIY instructions for those repairs. What we will do is tell you what’s likely wrong from the symptom, so you know what you’re dealing with before anyone comes out.
What Does Electric Gate Repair Cost in Killeen?
Electric gate repair in Killeen typically runs $200 to $900 for most problems, with operator replacement at $800 to $1,800 or more. The common electric repairs are control board replacement, receiver and remote issues, loop detector and safety sensor faults, and wiring problems. Control boards and operators sit at the top of the range because the part costs more and the reprogramming takes time. A sensor or receiver fix sits lower. When you call, tell us the brand and what the gate does (or doesn’t do), and we’ll give you a realistic range and then confirm it with a free written estimate on site.
Electric and automated gate repair is our core, not a side service. Control boards, operators, receivers, loop detectors, and the access hardware around them are what we do, and it’s the work most handymen won’t take on. If you want to understand the full scope of that work, see our Gate Repair Killeen page.
Repair or Replace: Which Costs Less in the Long Run?
Repair is almost always cheaper up front. A $300 to $500 repair on a gate with a good operator and frame beats a full replacement, and most Killeen gates we see are repairable. Replacement starts to win when the operator and the access control are both failing, when the panel or frame is structurally compromised, or when parts for an older system can’t be sourced and each repair is a patch on the next failure. We don’t push replacement. We diagnose first and replace only when necessary, and we’ll tell you honestly when a repair no longer makes financial sense.
If replacement is the right call, new gate installation is one of our three core services, so you’re not sourcing a second contractor. The estimate for installation is set per job after we look at the site and the access needs.
FAQs – Gate Repair Cost in Killeen
How much does gate repair cost in Killeen?
Gate repair in Killeen typically costs $150 to $450 for common fixes and $450 to $1,800 for major repairs like control board or operator replacement. The written estimate sets the final price, and estimates are free. Call (866) 722-0161 for an exact quote.
Is it cheaper to repair or replace a gate?
Repair is cheaper in most cases: a $300 to $500 fix usually beats a full replacement, and most gates can be repaired. Replacement makes more sense when the operator, access control, and frame are all failing. Call (866) 722-0161 and we’ll diagnose it and tell you which way the numbers point.
How much does electric gate repair cost?
Electric gate repair in Killeen usually runs $200 to $900, with operator replacement at $800 to $1,800 or more. Control board and operator jobs cost more than sensor or receiver fixes. Call (866) 722-0161 for a free estimate on your system.
Can you come today?
Same-day service is often possible. Call (866) 722-0161. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. A call outside dispatch hours is booked into the next opening.
How much does a new gate installation cost in Killeen?
New gate installation is estimated per job after we see the site and the access needs, since gate size, operator choice, and access control change the price. The written estimate sets the final number. Call (866) 722-0161 to set up a free on-site estimate.
Book Your Free Gate Repair Estimate
If your gate is stuck, off track, or the operator won’t respond, the fastest way to know what it will cost is a free estimate. We work gates only, we know your brand, and we tell you what’s wrong before we recommend anything. Call (866) 722-0161. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Same-day service is often available, and the written estimate sets the final price.
Pricing reflects the Killeen market as of 2026. Gate Repair Killeen offers free estimates – call (866) 722-0161.
Written by the team at Gate Repair Killeen.
What Our Customers Say
"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Eduardo Hernandez"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Javier Rodriguez"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Megan Doyle