Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Killeen?
Gate installation in Killeen typically runs $1,800 to $4,200 for a residential driveway gate supplied and installed, or $4,500 to $12,000+ for a full automated commercial swing or slide system. A basic single-panel manual gate for a standard side yard sits lower, around $900 to $1,600, while the operator, wiring, and access hardware usually account for $600 to $2,500 of the total. On a typical Killeen lot, the single biggest cost driver is the surface the posts have to set into, and the second is how much trenching is needed to get power to the operator.
Gate Installation Cost Breakdown (2026)
Here’s how the line items stack up for a Killeen gate job. Every figure below is an estimate. The written estimate you receive after we look at your property is what sets the final price.
| Line item | Typical range |
|---|---|
| Single swing gate (manual, residential) | $900 – $1,800 |
| Double swing gate (manual, residential) | $1,600 – $3,200 |
| Sliding gate (residential, manual) | $2,400 – $4,500 |
| Swing operator (single leaf) | $700 – $1,900 |
| Slide operator | $1,100 – $2,600 |
| Access hardware (keypad, remote, receiver) | $150 – $1,100 |
| Safety loops and photo-eye sensors | $250 – $900 |
| Power run / conduit and trenching | $300 – $2,200 |
| Concrete footings and post setting | $350 – $1,400 |
| Commercial swing or slide system (automated) | $4,500 – $12,000+ |
The panels themselves set the floor of the price. Sheet count and material matter: an aluminum residential gate costs less than a full ornamental or steel unit of the same span. After that, automation is the swing factor. A manual gate is a fence job with better hardware. An automated gate is an electrical job, and it needs an operator, a safe power path, sensors that stop the leaf when something crosses the threshold, and access devices on top. Labor around trenching for the power line is where a straightforward install turns into a longer day on a hard Central Texas lot.
Most of our Killeen customers land between $1,900 and $3,600 for a fully automated single driveway gate. Commercial access systems climb well past that because of duty ratings on the operators, heavier loops, and the access credentials the property manager needs to hand out. If you’re pricing a repair instead of a new gate, our gate repair in Killeen page covers what those visits cost.
What Affects Gate Installation Pricing in Killeen
- The soil and the surface. Much of Killeen sits on limestone and caliche under a shallow soil layer. Cutting post holes through that rock takes longer and sometimes a different tool, so footing labor on a rocky lot can run a few hundred dollars above the same gate on looser ground. Posts still have to go to proper footing depth on every job, rock or not.
- Where the driveway meets the street. A short drive close to the house means less fencing and a shorter trench to the power source. A long front drive on a lot in a neighborhood like Harker Heights, Copperas Cove, or the Skyline Estates area of Killeen adds panels, posts, and wire, and the total climbs with every added foot of span.
- Automation level. A single remote control is cheap. A keypad plus intercom plus vehicle loop is not. Property managers who need entry credentials for staff and delivery access usually spend more on the access layer than the homeowner who just wants a clicker on the sun visor.
- Operator duty rating. A light residential operator costs less than a commercial unit built to cycle hundreds of times a day. On a commercial property, going cheap on the operator means replacing it sooner, so the better-built unit tends to be the cheaper decision over the life of the gate.
- Existing gate or new build. If you already own a gate that’s simply worn out and you’d like to keep the brand logic you’re used to, we’ll service the system you have rather than selling you a whole new brand. That matters on the operator side. It’s often smarter to keep a working LiftMaster, FAAC, or DoorKing system and replace only what’s failed. The installation price changes depending on how much has to be new.
- Permits and property rules. Most cities require a permit for a fence or gate above a certain height, and some HOAs and commercial properties require approval before you install. Ask Killeen’s building department about the height threshold for your lot, and check with your property’s management before work begins. We can’t quote permit costs on a page, but we can tell you what a job will need when we look at it.
Which Gate Type Costs What in Killeen
The gate’s style and mechanism do as much to set the price as the operator does. Here’s the short version for each common type:
Swing Gates
Swing gates are the most common residential choice in Killeen because most driveways can take one. A single-leaf swing gate is the cheapest automated setup, at roughly $1,800 to $3,200 installed with a basic operator. Double swing gates run higher because they need either two operators or a tandem setup, and the pressure of the second leaf adds hardware. Swing gates need clear room to open, so a narrow or sloped driveway may push you toward a slide instead.
Sliding Gates
A slide gate needs a straight run of track and somewhere for the leaf to travel, so it suits a wider lot or one where the drive is short and there’s no room for the leaf to swing. Base installation runs $2,400 to $4,500 for a residential unit before the operator, because the track, rollers, and posts take more material. The operator adds another $1,100 to $2,600. On commercial properties, slide gates are common because they take up less driveway and work with a wider vehicle loop layout.
Commercial Access Systems
Small-to-mid commercial sites need a gate that cycles a lot, stops for a car crossing the path, and lets a property manager control who gets in. That’s where the price jumps into the $4,500 to $12,000+ range, and it can climb if the site needs multiple loops, a vehicle detector for a gate that opens only for cars pulling up, or an intercom to a front desk. This is the work the brand names get recognized on. DoorKing and FAAC systems are especially common on commercial properties, and we work on the system a property already runs.
Electric Gate Installation: What’s Included in the Price
A gate install on a Killeen property is really two jobs in one: the physical gate and the electrical system that moves it. We’re electric gate specialists first, so the automation is never an add-on to us. A proper install covers the operator mounted and aligned to the leaf, the power path from the source to the operator, the safety devices that stop the gate if something crosses its path, and the access hardware like a keypad, receiver, or loop. It also covers the setup that makes an operator live up to its rating: correct limits, a matched braking profile, and sensors wired so the gate reverses rather than resists.
We work across nine major gate brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That range matters on an install because each brand’s operator has its own logic, and we set up the one you choose by how it was built to run, not by generic guesswork. Our technicians have up to 13 years of experience, and the brand names are ones we see on the properties around Killeen every week.
We diagnose first and replace only when necessary. On an install that means we don’t push accessories you don’t need. You’ll get a written estimate with the line items laid out: gate, operator, access hardware, safety devices, power run, and footings. If a gate brand or operator is out of stock or an odd fit for your property, we’ll tell you and explain the tradeoff rather than force it.
How to Save on Gate Installation
There’s no getting around the biggest line items, but a few decisions lower the total without cutting corners:
- Keep a working gate and replace only the failed part. If your current gate is structurally sound and the operator has a common failure, repair can cost far less than a full new install. Our team handles that same-day in many cases.
- Stick with the brand you already know if it works. If a LiftMaster or Viking system has served the property well, replacing that brand’s operator is often simpler and cheaper than switching brands and reworking the access hardware to match.
- Get the estimate before you buy the gate yourself. A gate panel bought without checking the operator match can create a second visit and extra cost. A free on-site estimate lets us size the panel to the operator and the driveway in one pass.
- Bundle the access layer at once. Adding a keypad, receiver, and safety loop in the same visit costs less than calling us back for each piece separately.
- Ask about the power path early. If a dedicated circuit already sits near the gate post, the trenching portion shrinks. Point it out when we estimate.
Estimates are free and the price is set per job. Call (866) 722-0161 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Is It Cheaper to Repair or Replace a Gate in Killeen?
Repair is usually cheaper than replacement when the gate panel and posts are sound and only the operator, control board, receiver, or sensor has failed. A control board or receiver fix typically runs a fraction of a new automated install. Replacement makes more sense when the gate structure itself is bent, the posts are failing, or the panels have been hit enough that the frame no longer holds alignment.
We can’t price either path from a webpage, so the honest answer is to have it looked at. On-site, we diagnose the operator and the gate together, because a failing operator can be caused by a gate that’s dragging. Fixing the operator alone on a binding gate just buys you the same failure again. Call (866) 722-0161 for a free estimate.
How Long Does a Gate Installation Take?
A residential single swing gate with an operator is typically a one-day job once the site is ready. Double gates, slide gates, and commercial systems take longer, often two days or more depending on trenching and footing work. On limestone ground, the footing portion of a Killeen job can add time, so we’d rather tell you two days and finish early than promise a day and run into rock.
Can You Install a Gate on an HOA or Commercial Property in Killeen?
Yes. We work on both residential driveway gates and commercial access systems, and we’re used to the approval side. HOAs and commercial properties usually require a review before installation, so have that approval in hand before the install date. We’ll install to the plan that was approved, including the operator duty rating and access hardware the property needs. If the property already runs a particular brand, we’ll work with it rather than replacing the whole system to make our setup easier.
FAQs – Gate Installation Cost
How much does a driveway gate cost to install in Killeen?
A typical single automated driveway gate in Killeen costs $1,800 to $3,600 installed, with double gates and larger slides running $2,400 to $4,500 or more before the operator. The written estimate after an on-site look sets the final price. Call (866) 722-0161 for a free estimate.
Is it cheaper to repair or install a new gate?
Repair is usually cheaper when the gate panel and posts are still sound and only the operator or one of its parts has failed. A new installation is the better call when the structure is bent or the posts are failing. Either way, an on-site diagnosis tells you which side you’re on. Call (866) 722-0161 for a free estimate.
Do I need a permit to install a gate in Killeen?
Most cities require a permit for a fence or gate over a certain height, so ask Killeen’s building department about the threshold on your lot before work starts. Your HOA or commercial property management may also need to approve the plan first. We install to the approved plan and can walk you through what the job involves. Call (866) 722-0161 for a free estimate.
What brands of gate system can you install?
We work on nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We install the operator the property needs and service the brand you already run rather than pushing a switch. Call (866) 722-0161 for a free estimate.
How much does an electric gate operator cost in Killeen?
An operator alone typically costs $700 to $2,600 depending on whether it’s a single swing, double swing, or slide unit and how heavy-duty it needs to be. Adding the access hardware, safety loops, and power run pushes the installed electric portion to roughly $1,500 to $4,800. Call (866) 722-0161 for a free estimate.
Get a Free Estimate for Your Killeen Ground
Every lot in Killeen is different: the size of the drive, the rock under the surface, the distance to the power source, and the access hardware the property needs all change the number. We’ll look at the site, measure, and write the estimate with the line items clear. Call (866) 722-0161 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
For a broader look at local gate service and the work we do around Killeen, our team is one call away.
Pricing reflects the Killeen market as of 2026. Gate Repair Killeen offers free estimates. Call (866) 722-0161.
Written by the team at Gate Repair Killeen.
What Our Customers Say
"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Alicia Grant"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Laura Fletcher"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Javier Rodriguez