Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Killeen?
Gate parts and welding in Killeen typically run $95 to $450 for common repairs, with most hardware and on-site welding jobs landing between $150 and $300. A simple hinge or latch swap with a bit of touch-up welding sits at the low end, while a bent cantilever arm, a rebuilt frame weld, or a full operator board replacement pushes toward the top. The written estimate sets the final price, so the range you see here is a starting point, not a bill.
We’re a gates-only shop. Every technician on the job works on gates, not garage doors or general handyman lists, and our technicians have up to 13 years of experience diagnosing gate hardware and automation. That focus matters when a gate starts dragging, a weld cracks, or an operator stops responding. Call (866) 722-0161 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Most Killeen gate parts and welding jobs cost $95 to $450, with hardware replacement and small welds at the low end.
- A new operator or control board is the biggest single line item, often $350 to $1,100 in parts before labor.
- We work on your brand, not around it – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Diagnose first, replace only when necessary. We repair what can be repaired.
- Free estimates, and the price is set per job by the written estimate.
Gate Parts & Welding Cost Breakdown (2026)
Here’s what the common line items look like in the Killeen market this year. Ranges cover the part and the labor to fit it. Every job gets its own written estimate after we look at the gate.
| Line Item | Typical Range | Notes |
|---|---|---|
| Hinge, latch, or roller replacement | $95 – $220 | Per fitting; multiple fittings compound |
| Weld repair on frame or post | $150 – $350 | Depends on access and how much metal needs rebuilding |
| Gate arm or cantilever repair | $180 – $450 | Bent or seized arms often need new hardware plus welding |
| Safety loop or receiver replacement | $150 – $380 | Includes cutting and re-pouring a fresh loop in some cases |
| Control board replacement | $280 – $650 | Brand and board model drive the price |
| Operator motor replacement | $450 – $1,400 | Slide and swing operators differ widely; brand matters |
| Access hardware (keypad, entry station) | $120 – $400 | Wiring run length adds cost |
| Battery backup or solar add-on parts | $180 – $500 | Parts and install; site conditions vary |
What pushes a job up? Three things, mostly. Weight and size of the gate, because a heavy commercial leaf needs stouter hardware and more careful welding than a residential driveway gate. Access, because a gate hemmed in by fence line and landscaping takes longer to work around than one with open clearance. And brand, because a DoorKing control board and a Mighty Mule control board are not the same part at the same price. What keeps a job down? Catching the problem early. A latch that’s worn can be swapped for well under $200. A post that’s cracked all the way through and dragging the frame is a bigger weld and a bigger bill.
If the gate won’t move at all, the problem is often electrical before it’s mechanical. That’s where a gate repair Killeen visit usually starts: power, then operator, then the metal.
What Affects Gate Parts & Welding Pricing in Killeen
Killeen gates live outdoors in heat, dust, and windblown grit. That shapes what wears out and what the repair costs. Here’s what moves the number.
- Gate type and weight. A light residential swing gate and a heavy commercial slide gate need very different hardware. Heavier leaves mean thicker hinges, stronger welds, and an operator sized for the load. All of that adds to the estimate.
- Brand and part availability. Nine brands carry their own logic and their own parts catalogs. We’re familiar with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we know what to order and what fits. An off-brand or unknown system can mean a longer search for the right part.
- Condition of the existing metal. A clean crack welds fast. A post that’s been wobbling in the ground for a season, or a frame that’s been bent and re-bent, takes more time to prep and rebuild. That’s a different job.
- Electrical work involved. When a gate fails, we check the operator, control board, receivers, and safety loops before we touch the metal. If the board or operator needs replacing, that’s a bigger line item than hardware. We handle control boards, loop detectors, and receivers that most handymen won’t touch.
- Access and site conditions. A gate with open space around it is quicker to work on than one boxed in by landscaping, fencing, or a tight driveway. Access affects labor time, and labor time affects the price.
- Whether it’s repair or full replacement. A repair-forward approach almost always costs less. We diagnose first and replace only when necessary. But a gate that’s lost multiple posts and won’t hold an operator any longer may cost less to replace than to keep patching. New installation is one of our three core services, alongside Killeen gate repair and electric gate repair.
How to Save on Gate Parts & Welding
The biggest savings come from not letting a small problem become a big one. Here’s how to keep the bill down.
- Fix the wobble before it becomes a weld. A hinge that’s loose or a latch that’s grinding is cheap to fix. A post that’s cracked through and dragging the frame is not. Small hardware now beats structural welding later.
- Get an electric gate checked when it hesitates. A gate that reverses for no reason, ignores the remote, or stops halfway usually has a failing board, receiver, or loop, not a motor on its way out. Catching it early often means a smaller part instead of a whole operator. For gate automation in Killeen, that check happens fast.
- Stay with your brand. We service your existing gate brand rather than pushing a costly brand replacement. Brand-agnostic repair keeps your parts cost down.
- Ask for the estimate in writing. The written estimate is where the price lives. Get it before work starts so there are no surprises.
- Bundle small jobs into one visit. If you’ve got a squeaky hinge, a wobbly latch, and a remote that’s lost its signal, one visit handles all three. That’s fewer trips and a lower total than three separate calls.
Free estimates are part of how we work. Call (866) 722-0161 and we’ll come look at the gate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Can the Same Parts Fix Every Gate Brand in Killeen?
No. Each brand uses its own control boards, receivers, and operator hardware, so a DoorKing board won’t fit a Mighty Mule operator and a FAAC arm isn’t a BFT arm. That’s why brand familiarity saves you money: we know which parts go with which system, so we don’t waste time and labor guessing. When a gate is automated, the electrical side usually decides the cost, and that’s where electric gate repair becomes the real work. From opener to operator, we know the system before we order a single part.
What Happens When You Call About Gate Parts & Welding?
We start with a free estimate. A technician looks at the gate, checks the hardware and the operator, and writes up what needs to happen. If the metal is the problem, we plan the weld. If the operator or control board is the problem, we plan the electrical fix. Most calls on parts and small welds can be handled same-day when the schedule allows. For bigger operator replacements or full gate replacement, we book the work once the estimate is agreed.
One safety note: gate operators run on line power, and the wiring inside an operator enclosure can be dangerous if it’s handled without training. Heavy gate leaves can crush fingers or trap a person if a safety loop has failed. We check power, control boards, receivers, and loops before anything else, and we recommend a licensed electrician for any work outside the operator itself. We don’t give step-by-step instructions for opening a live operator because the risk isn’t worth it.
FAQs – Gate Parts & Welding Cost
How much does gate parts and welding cost in Killeen?
Most jobs land between $95 and $450, with hardware swaps and small welds at the low end and larger frame or operator work at the top. The written estimate sets the final price. Call (866) 722-0161 for an exact quote. Estimates are free.
How much does a new gate operator cost in Killeen?
A new operator typically runs $450 to $1,400 including installation, depending on the brand and whether it’s a slide or swing system. Control board replacement alone usually falls between $280 and $650. Call (866) 722-0161 for an exact quote. Estimates are free.
Is it cheaper to repair or replace a gate in Killeen?
Repair is almost always cheaper when the posts and frame are sound: a weld or hardware job at $95 to $450 beats a full replacement every time. Replacement only wins when the gate has lost multiple posts or can’t hold an operator safely. We diagnose first and replace only when necessary. Call (866) 722-0161 for an exact quote. Estimates are free.
Can you come today for gate parts and welding?
Same-day service is often possible when parts are on hand and the schedule allows. We answer 24/7 and dispatch from 7am to 7pm, Sunday through Friday. Call (866) 722-0161 for an exact quote. Estimates are free.
Do you work on my gate brand?
We work on nine major systems, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We service the brand you already own rather than requiring a costly brand replacement. Call (866) 722-0161 for an exact quote. Estimates are free.
Where Can You Get a Gate Parts & Welding Estimate in Killeen?
Call Gate Repair Killeen at (866) 722-0161 for a free estimate on gate parts and welding. We’re a gates-only specialist: repair, electric gate repair, and new installation under one brand, so you won’t need to call a second company. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. If you’re not sure whether you need a repair or a replacement, we’ll tell you straight after we’ve seen the gate.
Written by the team at Gate Repair Killeen.
Pricing reflects the Killeen market as of 2026. Gate Repair Killeen offers free estimates – call (866) 722-0161.
What Our Customers Say
"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Laura Fletcher"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
- Priya Sharma"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Megan Doyle